Search

Home / RCMMTING / Remote Controlled Vehicles & Parts
6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia 6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia 6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia 6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia 6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia 6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia 6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car in Saudi Arabia

6-Pack 32P Pinion Gears 11T 12T 13T 14T 15T 16T, Hardened Steel, 3.175mm Bore, for 1/10 Traxxas Arrma Axial HSP HPI Tamiya Losi RC Car

SAR 68

Brand
RCMMTING
Availability
In stock
– 1 +

Special Features

  • Tough hardened steel construction for superior strength and long wear
  • 6-pack set includes 11T 12T 13T 14T 15T 16T to fine-tune gear ratio
  • Fits 3.175mm shaft motors, secure and efficient power transfer
  • Works with 550 540 3650 size motors for 1/10 RC cars and trucks
  • Comes with 6 pinion gears, M4 set screws, and a hex wrench

Description

Specifications
Material: Hardened Steel
Pitch: 32P
Teeth: 11T 12T 13T 14T 15T 16T
Suitable shaft diameter: 3.175mm

Package List
1 × 11T Pinion Gear
1 × 12T Pinion Gear
1 × 13T Pinion Gear
1 × 14T Pinion Gear
1 × 15T Pinion Gear
1 × 16T Pinion Gear
6 × Grub Screws
1 × Hex Key

How to install the pinion gear
Loosen the motor first, then slide the pinion gear onto the motor shaft. Make sure you lock the grub screw on the flat portion of the shaft. When tightening the motor back down, leave a small gap between the pinion gear and the spur gear — about the thickness of a piece of paper. Check that the gears spin freely by hand before running. If the gap is too tight, the gears will wear quickly and overheat. If too loose, you risk stripping teeth under power.

Related Items


{"error":"Error","cart_limit":"You have too many items in your cart.","prod_limit":"You cannot add any more of this item"}